The Martin ExperienceAll material © 2009. Martin Audio Ltd. Subject to change without notice. OmniLine®System Preparation
All material © 2009. Martin Audio Ltd. Subject to change without notice. 92) Press the screws into the front of the polystyrene tray to avoid loosing
All material © 2009. Martin Audio Ltd. Subject to change without notice. 10 Remove the Orange Safety clip Remove the link Pins
All material © 2009. Martin Audio Ltd. Subject to change without notice. 11Tip! If the linking pins are difficult to remove, loosen the four link plat
All material © 2009. Martin Audio Ltd. Subject to change without notice. 125) Insert the four linking pins into the aligned link plate holes. 6)
All material © 2009. Martin Audio Ltd. Subject to change without notice. 134-Omniline® module wall mounting To remind you: Martin Audio Omniline® lo
All material © 2009. Martin Audio Ltd. Subject to change without notice. 146.2 If you haven’t already prepared Omniline® module splay angles as indic
All material © 2009. Martin Audio Ltd. Subject to change without notice. 156.5 Fit rear the rear covers - using the cut out version for the module wit
All material © 2009. Martin Audio Ltd. Subject to change without notice. 166 8-16 Omniline® module wall mounting To remind you: Martin Audio Omnilin
All material © 2009. Martin Audio Ltd. Subject to change without notice. 17 Interlock modules together Ensure that the tongues (right) are properly l
All material © 2009. Martin Audio Ltd. Subject to change without notice. 185) Remember to add the safety clips! 6) Wire the 4-module blocks toget
All material © 2009. Martin Audio Ltd. Subject to change without notice. 1 Martin Audio Omniline® system preparation Notes: A variety of mou
All material © 2009. Martin Audio Ltd. Subject to change without notice. 19 7) Screw the pcb to the inside of the most convenient rear cover using t
All material © 2009. Martin Audio Ltd. Subject to change without notice. 20Once you have fitted the U-bracket, angle the lower module to the required
All material © 2009. Martin Audio Ltd. Subject to change without notice. 21 Again, the bracket position and orientation will be determined by the angl
All material © 2009. Martin Audio Ltd. Subject to change without notice. 227.7 After removing the pin and R-clip from the DIN15315 wedge fastener, loa
All material © 2009. Martin Audio Ltd. Subject to change without notice. 237.8 Fit the top HAM02027 and bottom HAM02026 wall brackets onto the wall us
All material © 2009. Martin Audio Ltd. Subject to change without notice. 247.10 Shackle the end of the wire rope to the top wall bracket. 7.11 Use
All material © 2009. Martin Audio Ltd. Subject to change without notice. 258 Omniline® flying system To remind you: Martin Audio Omniline® loudspeak
All material © 2009. Martin Audio Ltd. Subject to change without notice. 263) Fit 4-module blocks together by interlocking modules together near the
All material © 2009. Martin Audio Ltd. Subject to change without notice. 274) Add the linking pins as shown in section 5.2 earlier. 5) Remember to
All material © 2009. Martin Audio Ltd. Subject to change without notice. 28 Notes: White = -ve and Orange = +ve Upper and lower block connections
All material © 2009. Martin Audio Ltd. Subject to change without notice. 2You will need the following tools for OmniLine preparation and installation.
All material © 2009. Martin Audio Ltd. Subject to change without notice. 298.2 Fit the HAM03191 flying bracket (arrowed) to the top Omniline® module o
All material © 2009. Martin Audio Ltd. Subject to change without notice. 30 HAM03192 tie bracket in place 8.4 Fit the second HAM03192 tie-bracket to
All material © 2009. Martin Audio Ltd. Subject to change without notice. 31Remove the linking pins if necessary and fit the bracket in the correct ori
All material © 2009. Martin Audio Ltd. Subject to change without notice. 329. Omniline Bottom Cover The Omniline Bottom Cover Plate An Omniline a
All material © 2009. Martin Audio Ltd. Subject to change without notice. 33always have a set of these left over as each block of four Omniline Starter
All material © 2009. Martin Audio Ltd. Subject to change without notice. 349.2 Position the bottom cover in place under the lowest module. You will fi
All material © 2009. Martin Audio Ltd. Subject to change without notice. 35 9.3 REPLACE ANY SAFETY CLIPS THAT YOU REMOVED!, then replace the backs of
All material © 2009. Martin Audio Ltd. Subject to change without notice. 31 Introduction Omniline® is a versatile, micro-line array designed for inst
All material © 2009. Martin Audio Ltd. Subject to change without notice. 4Omniline® module pack Each pack of OmniLine® modules comprises the following
All material © 2009. Martin Audio Ltd. Subject to change without notice. 5 4 x OmniLine® wall mounting kit Each 4 x OmniLine® wall mounting kit compri
All material © 2009. Martin Audio Ltd. Subject to change without notice. 6 8-16 x OmniLine® wall mounting kit Each 8-16 x OmniLine® wall mounting kit
All material © 2009. Martin Audio Ltd. Subject to change without notice. 7 OmniLine® flying kit Each OmniLine® flying kit comprises the following extr
All material © 2009. Martin Audio Ltd. Subject to change without notice. 85.1 System preparation To avoid flattening or damaging your OmniLine gril
Comments to this Manuals